DoALL
DoALL 2012-VH Vertical Contour Band Saw
Vertical contour saw with a hydraulically powered work table for controlled contour and straight cuts up to 20 inches wide
- Throat (Band to Column)
- 20 in (508 mm)
- Maximum Work Height
- 12 in (305 mm)
By Application
Sawing
When you need to cut solid stock and profiles to length, the right machine depends on what you are cutting. Band saws power through solid bar and structural stock, and miter saws cut aluminum extrusion and profiles to length. This is the equipment that turns stock into ready-to-work blanks.
The Lineup
Sawing Machines
DoALL
DoALL 2013-V2 Vertical Contour Band Saw
Dependable entry-level vertical contour saw with variable pulley drive for lower-production contour and straight cutting
- Throat (Band to Column)
- 20 in (508 mm)
- Maximum Work Height
- 13 in (330 mm)
DoALL
DoALL 2013-V3 Vertical Contour Band Saw
Mid-range vertical contour saw with a 3 HP variable frequency drive for versatile contour and straight cutting
- Throat (Band to Column)
- 20 in (508 mm)
- Maximum Work Height
- 13 in (330 mm)
DoALL
DoALL 2013-V5 High Speed Contour Band Saw
High-speed vertical contour saw with a 5 HP variable frequency drive for faster production cutting
- Throat (Band to Column)
- 20 in (508 mm)
- Maximum Work Height
- 13 in (330 mm)
DoALL
DoALL 3612-VH Vertical Contour Band Saw
Large 36 inch throat vertical contour saw with a hydraulically powered work table for big contour and straight cuts
- Throat (Band to Column)
- 36 in (915 mm)
- Maximum Work Height
- 12 in (305 mm)
DoALL
DoALL 3613-V3 Vertical Contour Band Saw
Large 36 inch throat vertical contour saw with a 3 HP inverter drive for versatile contour and straight cutting
- Throat (Band to Column)
- 36 in (915 mm)
- Maximum Work Height
- 13 in (330 mm)
DoALL
DoALL 3613-V5 High Speed Contour Band Saw
Large 36 inch throat high-speed contour saw with a 5 HP inverter drive and two-speed transmission for faster production
- Throat (Band to Column)
- 36 in (915 mm)
- Maximum Work Height
- 13 in (330 mm)
DoALL
DoALL 400S Full Cycle Band Saw
Introductory structural miter saw for extremely accurate straight and 45 degree cuts in smaller runs
- Round Tube
- 10.75 in (273 mm)
- Rectangle (W x H)
- 16 x 10 in (406 x 254 mm)
DoALL
DoALL 4824-VPL Vertical Plate Saw
Entry-capacity vertical plate saw for cutting solid plate and blocks up to 48 by 24 inches
- Cutting Capacity (Rectangle)
- 48 x 24 in (1200 x 600 mm)
- Work Height
- 51.2 in (1300 mm)
DoALL
DoALL 4848-VPL Vertical Plate Saw
Mid-capacity vertical plate saw for cutting solid plate and blocks up to 48 by 48 inches
- Cutting Capacity (Rectangle)
- 48 x 48 in (1200 x 1200 mm)
- Work Height
- 55.1 in (1400 mm)
DoALL
DoALL 4863-VPL Vertical Plate Saw
Largest-capacity vertical plate saw for cutting solid plate and blocks up to 48 by 63 inches
- Cutting Capacity (Rectangle)
- 48 x 63 in (1200 x 1600 mm)
- Work Height
- 55.1 in (1400 mm)
DoALL
DoALL DC-1000CNC Dual Column Enclosed CNC Band Saw
Extreme-capacity enclosed CNC band saw for automatic cutting of solids up to 33.5 inches round
- Round at 90 degrees (tube or solid)
- 33.45 in (850 mm)
- Rectangle at 90 degrees (H x W)
- 33.45 x 39.37 in (850 x 1000 mm)
DoALL
DoALL DC-1100SA Dual Column Semi-Automatic Band Saw
Large semi-automatic dual-column band saw for production cutting of heavy metals up to 43 inches round
- Round at 90 degrees
- 43.3 in (1100 mm)
- Rectangle at 90 degrees (W x H)
- 43.3 x 43.3 in (1100 x 1100 mm)
DoALL
DoALL DC-1400CNC Dual Column Table Band Saw
Maximum-capacity CNC table band saw for automatic cutting of the largest solids, up to 47 inches round
- Round at 90 degrees (tube or solid)
- 47.25 in (1200 mm)
- Rectangle at 90 degrees (H x W)
- 47.25 x 55.12 in (1200 x 1400 mm)
DoALL
DoALL DC-1700SA Dual Column Semi-Automatic Band Saw
The largest DoALL semi-automatic dual-column band saw, cutting round stock up to 51 inches
- Round at 90 degrees
- 51.2 in (1300 mm)
- Rectangle at 90 degrees (W x H)
- 67 x 51.2 in (1700 x 1300 mm)
DoALL
DoALL DC-280NC Production Band Saw
Compact automated NC band saw for high-production cutting of round and structural stock up to 11 inches
- Round at 90 degrees
- 11 in (280 mm)
- Rectangle at 90 degrees (W x H)
- 11.75 x 11 in (300 x 280 mm)
DoALL
DoALL DC-330NC Production Band Saw
Automated NC band saw for high-production cutting of a wide range of metals up to 13 inches round
- Round at 90 degrees
- 13 in (330 mm)
- Rectangle at 90 degrees (W x H)
- 15.75 x 13 in (400 x 330 mm)
DoALL
DoALL DC-330SA Semi-Automatic Band Saw
Affordable semi-automatic dual-column band saw for shops that cut a wide range of metals up to 13 inches round
- Round at 90 degrees
- 13 in (330 mm)
- Rectangle at 90 degrees (W x H)
- 15.75 x 13 in (400 x 330 mm)
DoALL
DoALL DC-420NC Production Band Saw
Automated NC band saw built to run at peak performance day in and day out, up to 16.5 inches round
- Round at 90 degrees
- 16.5 in (420 mm)
- Rectangle at 90 degrees (W x H)
- 16.5 x 16.5 in (420 x 420 mm)
DoALL
DoALL DC-440CNC-A Dual Column Enclosed CNC Band Saw
Fully automatic enclosed CNC band saw from the Hercules line for round stock up to 17.25 inches
- Round at 90 degrees
- 17.25 in
- Rectangle at 90 degrees (W x H)
- 18 x 16 in
DoALL
DoALL DC-460NC Production Band Saw
Automated NC band saw for high-production cutting of a wide range of metals up to 18 inches round
- Round at 90 degrees
- 18 in (460 mm)
- Rectangle at 90 degrees (W x H)
- 20 x 18 in (510 x 460 mm)
DoALL
DoALL DC-510CNC Dual Column Enclosed CNC Band Saw
Fully automated enclosed CNC band saw with Siemens control for industrial cutting up to 20 inches round
- Round at 90 degrees
- 20 in (510 mm)
- Rectangle at 90 degrees (W x H)
- 20 x 20 in (510 x 510 mm)
DoALL
DoALL DC-560NC Production Band Saw
Large-capacity automated NC band saw for production cutting of a wide range of metals up to 22 inches round
- Round at 90 degrees
- 22 in (560 mm)
- Rectangle at 90 degrees (W x H)
- 24 x 22 in (610 x 560 mm)
DoALL
DoALL DC-560SA Semi-Automatic Band Saw
Large-capacity semi-automatic dual-column band saw for production cutting of a wide range of metals up to 22 inches round
- Round at 90 degrees
- 22 in (560 mm)
- Rectangle at 90 degrees (W x H)
- 31.5 x 22 in
DoALL
DoALL DC-620CNC Dual Column Ball Screw Band Saw
High-speed enclosed CNC saw with servo ball-screw feed and 20 HP drive for efficient automatic production
- Round at 90 degrees
- 21.5 in (550 mm)
- Rectangle at 90 degrees (W x H)
- 24.5 x 21.5 in (620 x 550 mm)
DoALL
DoALL DC-700NC Production Band Saw
Heavy-duty automated NC band saw benchmarked for automotive and heavy machinery parts, up to 27 inches round
- Round at 90 degrees
- 27 in (700 mm)
- Rectangle at 90 degrees (W x H)
- 31 x 27 in (800 x 700 mm)
DoALL
DoALL DC-750CNC Dual Column Enclosed CNC Band Saw
Large-capacity enclosed CNC band saw from the Hercules line for fully automatic cutting up to 28 inches
- Round at 90 degrees (solid)
- 27.5 in (700 mm)
- Round at 90 degrees (tube)
- 28 in (700 mm)
DoALL
DoALL DC-800NC Production Band Saw
Top-capacity automated NC band saw for the heaviest production cutting, up to 1000mm wide
- Rectangle at 90 degrees (W x H)
- 39.5 x 31.5 in (1000 x 800 mm)
DoALL
DoALL DC-800SA Semi-Automatic Band Saw
Heavy-duty semi-automatic dual-column band saw for production cutting of large metals up to 31.5 inches round
- Round at 90 degrees
- 31.5 in (800 mm)
- Rectangle at 90 degrees (W x H)
- 39.5 x 31.5 in (1000 x 800 mm)
DoALL
DoALL DCDS-600CNC Dual Column Dual Miter Band Saw
Fully automatic dual-column dual-swivel CNC band saw for high-production mitering to 60 degrees either way
- Round Tube
- 18.5 in (470 mm)
- Rectangle (W x H)
- 24 x 17.25 in (610 x 440 mm)
DoALL
DoALL DCDS-600SA Dual Column Semi-Automatic Band Saw
High-production dual-column semi-automatic dual-miter band saw, cutting to 60 degrees left and right
- Round Tube
- 18.5 in (470 mm)
- Round Solid
- 8 in (205 mm)
DoALL
DoALL DCDS-750CNC Dual Column Dual Miter Band Saw
Top-of-the-line dual-column dual-swivel CNC band saw for extreme high-production mitering
- Hollow Tube
- 19.5 in (500 mm)
- Round Solid
- 9 in (229 mm)
DoALL
DoALL DCDS-750SA Dual Column Semi-Automatic Band Saw
Large dual-column semi-automatic dual-miter band saw for structural, tube, stainless, and tool steel
- Round Tube
- 19.5 in (500 mm)
- Round Solid
- 9 in (230 mm)
DoALL
DoALL DS-280M Dual-Miter Manual Band Saw
Manual dual-miter band saw for precise low-volume cuts, mitering 45 degrees left to 60 degrees right
- Round Tube
- 9 in (230 mm)
- Rectangle (W x H)
- 11 x 8 in (280 x 210 mm)
DoALL
DoALL DS-320SA Dual-Miter Semi-Automatic Band Saw
Semi-automatic dual-miter band saw for low-volume vertical and angular cutting up to 60 degrees
- Rectangle (W x H)
- 12.5 x 11.75 in (320 x 300 mm)
- Miter/Swivel Angle
- 45 to 60 degrees
DoALL
DoALL DS-500SA Dual-Miter Semi-Automatic Band Saw
Semi-automatic StructurALL dual-miter band saw for linear and angled cutting, mitering 60 degrees either way
- Round Tube
- 14 in (356 mm)
- Rectangle (W x H)
- 19.5 x 13 in (495 x 330 mm)
DoALL
DoALL DS-600SA Dual-Miter Semi-Automatic Band Saw
Large semi-automatic dual-miter band saw for tubing and structural shapes, mitering 60 degrees left and right
- Round Tube
- 18 in (460 mm)
- Rectangle (W x H)
- 23.5 x 18 in (600 x 460 mm)
DoALL
DoALL S-320CNC Automatic CNC Swivel Band Saw
Automatic CNC scissor-style miter saw with hydraulic indexing for low to medium production
- Round Tube
- 11.75 in (300 mm)
- Rectangle (W x H)
- 12.5 x 11.75 in (320 x 300 mm)
DoALL
DoALL S-500CNC Miter CNC Band Saw
Automatic CNC scissor-head miter band saw with programmable indexing for production cutting up to 14 inches round
- Round Tube
- 14 in (356 mm)
- Rectangle (W x H)
- 19.5 x 13.25 in (495 x 337 mm)
DoALL
DoALL SC-100A Circular Saw
Automated CNC circular saw with integrated bar loading for round material up to 4 inches
- Round at 90 degrees
- Up to 4 in (102 mm)
- Rectangle at 90 degrees (H x W)
- 0.39 to 3.15 x 0.39 to 3.15 in (10 to 80 x 10 to 80 mm)
DoALL
DoALL SC-150A Circular Saw
Heavy-duty circular saw with rigid frame construction for round material up to 5.9 inches
- Round at 90 degrees
- Up to 5.9 in (150 mm)
- Rectangle at 90 degrees (H x W)
- 2.76 to 4.33 x 2.76 to 4.33 in (65 to 105 x 65 to 105 mm)
DoALL
DoALL SC-75A Circular Saw
Economical automated cold saw with CNC controls for round material up to 3 inches
- Round at 90 degrees
- Up to 3 in (75 mm)
- Rectangle at 90 degrees (H x W)
- 0.32 to 2.36 x 0.32 to 2.36 in (8 to 60 x 8 to 60 mm)
DoALL
DoALL TDC-1000CNC Dual Column CNC Tube Band Saw
Automatic CNC dual-column tube saw for large tube and pipe up to 40 inches with digital angle cutting
- Round Tube
- 40 in (1000 mm)
- Round Solid
- 21.7 in (550 mm)
DoALL
DoALL TDC-1000SA Dual Column Tube Band Saw
Semi-automatic dual-column tube saw for high-production cutting of large tube up to 40 inches
- Round Tube
- 40 in (1000 mm)
- Round Solid
- 21.7 in (550 mm)
DoALL
DoALL TDC-400CNC Dual Column CNC Tube Band Saw
Automatic CNC dual-column tube saw for high-production square-end cutting of tube up to 16 inches
- Round Tube
- 16 in (400 mm)
- Rectangle
- 16 x 16 in (400 x 400 mm)
DoALL
DoALL TF-2028M Vertical Tilt Frame Band Saw
Vertical tilt-frame band saw with a 7 degree cant design for easy entry and exit when cutting structural material
- Width
- 20 in
- Height
- 28 in
DoALL
DoALL Zephyr ZV-3620 Vertical Contour Band Saw
Zephyr flagship vertical contour saw with a 15 HP drive and speeds to 15,000 fpm for high-speed cutting of tough alloys
- Throat (Band to Column)
- 36 in (914 mm)
- Maximum Work Height
- 20 in (508 mm)
Mecal
Mecal FE 400 Vico-3
Double mitre saw purpose-built for steel profile cutting with heavy-duty blade and clamping system
- Blade Diameter
- 400 mm (15.74 in)
- Cutting Angles
- NC, any angle 135° to 45° (inward and outward)
Mecal
Mecal Single Saws
Single head cold saws for precise cutting of aluminum, PVC, and light alloy profiles
Mecal
Mecal SW 453 Argus
500mm double mitre saw with pneumatic head positioning and touch screen PLC for aluminum and PVC
- Blade Diameter
- 500 mm (19.68 in)
- Cutting Angles
- 90° / 45° / 22.5° (outward)
Mecal
Mecal SW 453 Argus-3
500mm 3-head double mitre saw for high-volume aluminum and PVC profile cutting
- Blade Diameter
- 500 mm (19.68 in)
- Cutting Angles
- NC servo, any angle 90° to 22.5° (outward)
Mecal
Mecal SW 453 Plug
Entry-level 500mm double mitre saw with 7-inch touch screen PLC for aluminum and PVC cutting
- Blade Diameter
- 500 mm (19.68 in)
- Cutting Angles
- 90° / 45° / 22.5° (outward)
Mecal
Mecal SW 453 Reverse Garda
500mm reverse blade double mitre saw for aluminum and PVC with automatic clamp synchronization
- Blade Diameter
- 500 mm (19.68 in)
- Cutting Angles
- 135° / 90° / 45° / 22.5° (inward and outward)
Mecal
Mecal SW 453 Reverse Garda-3
500mm 3-head reverse blade double mitre saw for high-volume aluminum and PVC production
- Blade Diameter
- 500 mm (19.68 in)
- Cutting Angles
- NC servo, any angle 135° to 22.5° (inward and outward)
Mecal
Mecal SW 553 Argus
550mm double mitre saw with 10-inch Magelis touch screen HMI and LED status strips
- Blade Diameter
- 550 mm (21.65 in)
- Cutting Angles
- 90° / 45° / 22.5° (outward)
Mecal
Mecal SW 553 Reverse Garda
550mm reverse blade double mitre saw with Magelis HMI for aluminum and PVC profile production
- Blade Diameter
- 550 mm (21.65 in)
- Cutting Angles
- 135° / 90° / 45° / 22.5° (inward and outward)
Mecal
Mecal SW 553 Reverse Garda-3
550mm 3-head reverse blade double mitre saw for the highest volume aluminum and PVC cutting operations
- Blade Diameter
- 550 mm (21.65 in)
- Cutting Angles
- NC servo, any angle 135° to 22.5° (inward and outward)
Mecal
Mecal TDC 622 Dynacut
3 axis 600mm double mitre saw with unique radial linear feed for 600mm cutting capacity
- Blade Diameter
- 600 mm (23.62 in)
- Cutting Width
- Up to 500 mm at 90°
Mecal
Mecal TDC 622 Edgemaster
5 axis 600mm double mitre saw with compound blade feed and 600mm cutting capacity for aluminum and PVC
- Blade Diameter
- 600 mm (23.62 in)
- Cutting Width
- Up to 500 mm at 90°
Buyer Guidance
How to Choose
When you are cutting solid bar and structural stock, a band saw is the right tool. It powers through round, square, and structural sections that a shear cannot handle, cutting them clean and square for the next operation.
For aluminum extrusion and profiles, a miter saw cuts to length with the angle accuracy that frame and assembly work demands. Match the saw to your stock and you keep the right machine on the right material.
Not Sure Which Machine Is Right for Your Shop?
Carlson's team has placed equipment in New England fabrication shops for over 67 years. We know which machine fits your material, your volume, and your floor plan. Call us or send a note and we will get back to you the same day.